800.660.0809 // 806.372.8300

Health Hazard
0

Fire Hazard
1

Physical Hazard
0

Personal Protection
 B

SciCron Technologies, LLC

MATERIAL SAFETY DATA SHEET


NFPA RATING


SECTION I - PRODUCT AND COMPANY IDENTIFICATION

TRADE NAME: PVC-100™, PVC-300™, PVC-350™

GENERIC NAME: Static Dissipative PVC Sheet

MSDS NUMBER: SC-003

DATE ISSUED: March 23, 2004

MANUFACTURER: SciCron Technologies, LLC

ADDRESS: 501 Amarillo Blvd. West

CITY, STATE, ZIP: Amarillo, TX 79107

MANUFACTURER PHONE: 806-372-8300

MANUFACTURER FAX: 806-372-8333

EMERGENCY (PLANT MANAGER): 806-372-8300

SECTION II - COMPOSITION/INFORMATION ON INGREDIENTS

This product consists primarily of high molecular weight PVC polymers which are not hazardous under Federal OSHA regulations.

SECTION III - HAZARDS IDENTIFICATION

EMERGENCY OVERVIEW: There are no significant health hazards associated with exposure to this product.
Fabrication: The product is a solid sheet material. Cutting and fabricating activities utilizing impact or power equipment may release small chips or shards, which are a hazard to the eyes. Grinding and sanding operations may release small quantities of dust with particles generally larger than respirable size.
Burning: Toxic gases and fumes are given off during burning or thermal decomposition. Burning produces intense heat and dense smoke.

SIGNS AND SYMPTOMS OF OVEREXPOSURE: Overexposure to this product is not likely to cause any significant acute effect.

HMIS RATING: Health: 0 Fire: 1 Physical Hazard: 0 Personal Protection: B

POTENTIAL HEALTH EFFECTS:
  • ROUTES OF ENTRY: Eyes, Inhalation

  • ACUTE EFFECTS: Coarse dust and particulate generated during fabrication can irritate eyes, nasal passages, and the upper respiratory system.

  • CHRONIC EFFECTS: Chronic effects are unlikely.

  • MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: Chronic respiratory disease.

  • CARCINOGENICITY: This product is not classified or regulated by NTP, IARC, or OSHA.

SECTION IV - FIRST AID MEASURES

EYE CONTACT: To remove particulate matter, flush with large amounts of water until irritation subsides. See a physician if irritation persists.

INHALATION: Blow nose and rinse mouth with water to clear dust and particulate. If exposed to excessive levels of dust or fumes, remove to fresh air and get medical attention if cough or other symptoms develop.

SECTION V - FIRE FIGHTING MEASURES

NFPA RATING: Health: 0 Fire: 1 Reactivity: 0 Other: --

FLASH POINT AND METHOD: Not applicable.

EXTINGUISHING METHOD: CO2, dry chemical, water spray and foam.

NFPA FIRE FIGHTING PROCEDURES: Use water spray, foam, dry chemical, or CO2 applied from a safe distance to avoid exposure to hazardous vapors and other decomposition products.

FIRE OR EXPLOSION HAZARDS: Product is a combustible thermoplastic resin but it will not continue to burn after ignition without an external fire source. Because of the potential for dense smoke in a fire situation, fire fighters should wear approved self-contained breathing apparatus.

HARMFUL COMBUSTION PRODUCTS: Intense heat, smoke, irritating toxic gases, and aerosols, including carbon dioxide, carbon monoxide, and hydrogen chloride, and metal oxides (no heavy metals) may be generated by thermal decomposition when the product undergoes combustion.

SECTION VI - ACCIDENTAL RELEASE MEASURES

SPILL OR LEAK PROCEDURES: Sweep or pick-up fabrication debris. Debris may usually be disposed of in a non-regulated landfill. However, prior to disposal, it is recommended that the regulations in effect for the particular area where disposal is to take place be checked to prevent improper disposal.

SECTION VII - HANDLING AND STORAGE

STORAGE TEMPERATURE: Store in well ventilated areas at temperatures below 120° F (49° C).

SPECIAL SENSITIVITY: None

HANDLING PRECAUTIONS: Use good housekeeping procedures to minimize the accumulation of dust during fabrication procedures.

SECTION VIII - EXPOSURE CONTROLS/PERSONAL PROTECTION

EYE PROTECTION: Wear safety glasses or face shields when cutting or machining.

SKIN PROTECTION: Gloves are recommended when fabricating due to possible sharp edges.

RESPIRATORY PROTECTION: For nuisance dust not otherwise regulated, observe the OSHA PEL of 15 mg/m3. When exposures over the PEL are encountered and engineering or other controls are not adequate to reduce airborne concentrations to below the PEL, use a dust mask such as 3M-8710 or equivalent.

SECTION IX - PHYSICAL AND CHEMICAL PROPERTIES

PRODUCT USES: Fabricated sheet items including glazing, display components, machine covers, and safety shields.

PHYSICAL FORM: Clear, tinted, or opaque thermoplastic sheet.

SPECIFIC GRAVITY: 1.38

MELTING POINT: N/A

SOFTENING POINT: 150° - 180° F (66° - 82° C)

SECTION X - REACTIVITY

STABILITY: Product is stable under normal conditions.

HAZARDOUS POLYMERIZATION: Will not occur.

INCOMPATIBILITIES: None in designed use.

DECOMPOSITION PRODUCTS: Burning or thermal decomposition may generate carbon monoxide, carbon dioxide, hydrogen chloride gas and trace amounts of metal oxides.

CONDITIONS TO AVOID: Exposure to high temperatures and direct flame.

SECTION XI - TOXICOLOGICAL INFORMATION

TOXICOLOGICAL HAZARDS: A review of the scientific literature did not indicate any specific toxicological hazard for PVC sheet.

SECTION XII - ECOLOGICAL INFORMATION

ECOLOGICAL INFORMATION: No data available.

SECTION XIII DISPOSAL CONSIDERATIONS

Product is non-hazardous. It may be incinerated or disposed of in a landfill in compliance with federal, state and local environmental regulations. Check before disposal to determine the details of such regulations in your area.

SECTION XIV - TRANSPORTATION CONSIDERATIONS

DOT NAME: Not regulated

DOT LABEL: Not applicable

DOT HAZARD CLASS: Not applicable

UN/NA NUMBER: None

PACKAGING GROUP: None

FLAMMABILITY CLASS: None

SECTION XV - REGULATORY INFORMATION

OSHA STATUS: This product is not considered hazardous under OSHA criteria (see Section III).

TSCA STATUS: Components of this product are included in the TSCA inventory.

CERCLA REPORTABLE QUANTITY: N/A

SARA TITLE III

SECTION 302 EXTREMELY HAZARDOUS: This product contains no extremely hazardous substances
as defined and listed in section #302.

SECTION 311/312 HAZARDOUS CATEGORIES: Not reportable under this section.

SECTION 313 TOXIC CHEMICALS: Not reportable under this section.

SECTION XVI - APPROVALS

REASON FOR ISSUE: General Update

PREPARED BY: Jack Clifford

APPROVAL DATE: March 23, 2004

SUPERSEDES DATE: May 1, 1996

SECTION XVII - DISCLAIMER

AS OF THE DATE OF THIS DOCUMENT, THE FOREGOING INFORMATION IS BELIEVED TO BE ACCURATE AND IS PROVIDED IN GOOD FAITH TO COMPLY WITH APPLICABLE FEDERAL AND STATE LAWS. HOWEVER, NO WARRANTY OR REPRESENTATION OF LAW OR FACT, WITH RESPECT TO SUCH INFORMATION, IS INTENDED OR GIVEN.